Elite 2500 + Subaru Liberty/Legacy Gen 4 3.0R & GT Plug 'n' Play Adaptor Harness Kit (HT-151356)

Everything a Gen 4 Liberty / Legacy needs to run on a Haltech Elite 2500, in one box, with no factory wires cut.

The Haltech Elite 2500 + Subaru Liberty/Legacy Gen 4 3.0R & GT Plug 'n' Play Adaptor Harness Kit pairs the Elite 2500 ECU with the vehicle-specific plug 'n' play adaptor harness. One side of the adaptor carries the factory ECU connectors, the other plugs into the Elite, so the Elite 2500 drops in where the stock ECU sat and the factory loom is never touched. It suits the MY04/05 Gen 4 Liberty / Legacy 3.0R (EZ30) and GT (EJ20) in JDM and Australian-delivered form only. It does not suit USDM Legacy models.

The Elite 2500 is Haltech's top-of-the-range Elite: eight injector and eight ignition outputs, drive-by-wire, control of up to four variable cams, dual-channel knock control and the full race function set. It is tuned in Haltech's NSP software, the same package used by the Nexus range.

What You'll Feel

• Drive-by-wire throttle and variable cam control kept, and mapped for your build
• A flat six or EJ20 that can finally be tuned properly for boost
• Dual-channel knock control and 4D closed-loop boost, so you can lean on the tune without leaning on luck
• A stock harness you can return to at any time

Features

• Plug 'n' play adaptor with the Subaru Liberty/Legacy Gen 4 3.0R & GT factory ECU connector layout
• Elite 2500 ECU: 8 injector and 8 ignition outputs, suits 1 to 12 cylinder and 2 to 4 rotor engines
• No cutting or splicing of the factory harness, fully reversible
• Includes an M14 x 1.5 air temp sensor with plug and pins, so the ECU sees real intake temperature from day one
• Auxiliary I/O 16-pin Tyco plug and pins for extra sensors and outputs (wideband, fuel and oil pressure, flex fuel)
• Tuned with Haltech NSP software over USB, with on-board and laptop data logging
• Haltech quick start guide walks through the fit
• Backed by the Haltech limited warranty

Elite 2500 ECU Specifications

• Injector outputs: 8 (peak and hold)
• Ignition outputs: 8
• Analog voltage inputs: 10
• Synchronised pulsed inputs: 4
• Digital pulsed outputs: 5
• Half-bridge outputs: 4 Stepper / 2 DBW
• Knock sensor inputs: 2
• CAN bus networks: 2
• MAP sensor: Internal (4 BAR)
• Drive-by-wire throttle: Single
• Variable cam control: Up to 4
• Boost control: 4D Closed Loop
• Flex fuel: Yes
• Launch control: Yes
• Traction control: Yes
• Anti-lag / rotational idle: Yes
• Long-term learning: Up to 4D
• Tuning table resolution: 32x32x8 4D
• On-board storage: 8MB

The Details

Part number HT-151356. Plug 'n' Play replacement of the factory ECU for Subaru Liberty/Legacy Gen 4 3.0R (EZ30) & GT (EJ20) MY04/05 (JDM & Australian Delivered Only). Unsure whether your car matches? Send us the VIN or a photo of the factory ECU plug before ordering and we will confirm.

Kit Includes

• 1x Elite 2500 ECU with DBW and Race Functions
• 1x Injection molded plastic plug 'n' play adaptor harness
• 1x M14 x 1.5 air temp sensor with matching plug and pins
• 1x Auxiliary I/O 16 Pin TYCO plug and pins
• 1x USB programming cable

Applications

• Subaru Liberty/Legacy Gen 4 3.0R & GT, EZ30 3.0R and EJ20 GT

Tuned By Shawn is a Platinum Haltech Dealer with in-house wiring and remote tuning. Add a remote tune and we will have the base map configured for your combination before the ECU ships.