Haltech uC-10 Digital Dash (HT-068000)

Ten inches of optically bonded colour, and enough I/O to run as its own data hub.

The Haltech uC-10 is a 10 inch full colour digital dash with a 1280 x 480 optically bonded screen that stays readable in any light. Screen layouts are fully customisable in Haltech NSP, the same software you tune your Nexus with. It talks to Haltech CAN, OBD-II, and a range of aftermarket ECUs, or it can be wired in as a complete stand-alone unit and used as an I/O expander in an existing Haltech setup.

What You'll See

A wide, crisp screen laid out exactly how you want it: gauges where your eyes land, warnings that demand attention, and a 14 LED RGB shift light across the top. Design your own pages in NSP, switch to a reverse camera feed when you need it, and let the twin ambient light sensors handle brightness from midday sun to a night session.

Features

• 10 inch full colour, optically bonded TFT screen, 1280 x 480 resolution
• 600+ lumens, dimmable, with 2 onboard ambient light sensors
• 70 degree minimum viewing angle, vertical and horizontal
• Fully customisable screen layouts in Haltech NSP
• 14 RGB shift lights
• 512MB onboard looped datalogging
• 6 digit odometer
• Camera input (composite video) with mirror and 0/90/180/270 degree rotation, plus a dedicated 12V / 500mA camera power output
• Wi-Fi, 2.4 GHz, with included glass mount antenna
• IP64 rated: dust-tight and protected against water splashes

The Details

• SKU: HT-068000
• Dimensions: 291.2 x 126.0 x 26.0 mm, excluding rear connectors
• Operating voltage: 6.5V to 20.0V
• Ambient temperature: -10 C (14 F) to +80 C (176 F)
• Inputs and outputs: 10 x analog voltage inputs, 4 x synchronised pulsed inputs, 4 x digital pulsed outputs, 1 x 5V output, 1 x 12V output, 1 x signal ground, dedicated tacho input, dedicated alternator excite
• Connectors: 34 pin AMP Superseal (auxiliary), female RP-SMA (Wi-Fi antenna)
• Communications: CAN (Haltech, OBD-II, or supported third party ECU), USB-A to USB-C
• Camera formats: NTSC 720 x 480, PAL 720 x 576

Kit Includes

• Haltech uC-10 Digital Dash
• 34 pin connector (same as HT-131001)
• Haltech DTM-4 to DTM-4 CAN cable, 3.0 m (118 in)
• USB-C cable
• 3 x M5 x 8 mm mounting screws
• 2 x momentary switches, pre-terminated 800 mm 22AWG cable
• Glass mount Wi-Fi antenna (2.4 GHz)
• Quick Start Guide
• Haltech fabric keytag and stickers

Applications

Suits all current Haltech ECUs via CAN. Also plug and play compatible with the following aftermarket ECU protocols: Hondata, Link G4, MaxxECU, Microtech, MoTeC M1 series, MoTeC hundred series (M400, M600, M800 gold box ECUs), and Syvecs. Can also be wired as a complete stand-alone dash.

Not included / sold separately: OBD-II connection requires the OBD-II to CAN cable (HT-135003). Mounting hardware is not included: see the uC-10 Moulded Panel Mount (HT-060091), iC-7/uC-10 Standard Dash Mount (HT-060070), and iC-7/uC-10 Tube Mount (HT-060072). Reverse camera sold separately.

Unsure about fitment for your build? Send us your engine and chassis details before ordering and we will confirm compatibility.

Tuned By Shawn is a Platinum Haltech Dealer. We can build the dash harness in house, and lay out your NSP screens and set up the uC-10 I/O during a live remote tuning session over Zoom.