{"product_id":"id1300-xds-fuel-injectors-single-injector-48mm-14mm-adapter-top-15mm-lower-o-ring-1300-48-14-15","title":"Injector Dynamics ID1300-XDS Fuel Injectors | Single Injector | 48mm, 14mm Adapter Top, 15mm Lower O-Ring (1300.48.14.15)","description":"\u003cp\u003e\u003cstrong\u003eChasing lean spikes at high boost? Your injectors are the weak link.\u003c\/strong\u003e\u003c\/p\u003e \u003cp\u003eA factory fuel system that was sized for stock power runs out of injector long before a built engine runs out of airflow, and 48mm, 14mm Adapter Top, 15mm Lower O-Ring builds hit that wall early. The \u003cstrong\u003eID1300-XDS\u003c\/strong\u003e (the current evolution of the ID1300x) answers that with 1335cc\/min of flow at 3.0 bar, compatibility with all known fuels, built for E85, delivered for your 48mm, 14mm Adapter Top, 15mm Lower O-Ring. Each set is flow matched using Dual Slope Matching and backed by full characterization data, so your ECU gets real numbers, not estimates. Sized right, characterized right, tuned right.\u003c\/p\u003e \u003ch3\u003eWhat You'll Feel\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCylinder-to-cylinder consistency you can see in your lambda and EGT logs\u003c\/li\u003e\n\u003cli\u003eCrisp part-throttle response instead of the surge and stumble big injectors are known for\u003c\/li\u003e\n\u003cli\u003eFaster dyno sessions, because accurate injector data means less time chasing fuel trims\u003c\/li\u003e\n\u003cli\u003eHeadroom to grow the build without touching the fuel system again\u003c\/li\u003e\n\u003cli\u003eFuel trims that stay put season to season instead of drifting with the weather\u003c\/li\u003e\n\u003c\/ul\u003e \u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eNominal flow rate: 1335cc\/min at 3.0 bar (43.5 psi), measured with iso-octane at 52 degrees C\u003c\/li\u003e\n\u003cli\u003eMaximum differential fuel pressure: 7.0 bar (101.5 psi)\u003c\/li\u003e\n\u003cli\u003eCompatible with all known fuels and designed specifically for alternative fuels like E85\u003c\/li\u003e\n\u003cli\u003eUSCAR electrical connector\u003c\/li\u003e\n\u003cli\u003eConfiguration: 48mm body, 14mm adapter top, 15mm lower o-ring\u003c\/li\u003e\n\u003cli\u003eSupplied as a flow-matched set with Dual Slope Matching for consistent delivery at low pulse widths\u003c\/li\u003e\n\u003cli\u003eAll stainless internals stand up to the corrosive nature of alcohol fuels\u003c\/li\u003e\n\u003c\/ul\u003e \u003ch3\u003eThe Details\u003c\/h3\u003e\u003cp\u003eThe ID1300-XDS was designed in partnership with Bosch Motorsport with alternative fuels in mind, and its stainless internals shrug off the corrosive side of alcohol better than anything else in this flow class. It was also built with the occasional switch back to gasoline in mind, with a minimum fuel mass low enough to idle and cruise cleanly on pump gas. Dual Slope Matching keeps cylinder-to-cylinder delivery consistent at the short pulse widths where high flow injectors usually fall apart. Every set ships flow matched, and Injector Dynamics publishes full characterization data, including slope, offset (dead time) versus voltage and pressure, and short pulse width behavior, so your tuner can load real numbers instead of chasing fuel trims across the map. Accurate dead times are what make large injectors behave at idle and cruise, and they are the reason these tune quickly and stay tuned. This configuration uses machined top adapters (already fitted) to suit the rail height listed above. If your harness does not have USCAR plugs, plug and play connector adapters are available separately, no cutting or soldering required.\u003c\/p\u003e \u003ch3\u003eKit Includes\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e[SPEC: KIT CONTENTS WITH QUANTITIES]\u003c\/li\u003e\u003c\/ul\u003e \u003ch3\u003eApplications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUniversal, 48mm body, 14mm adapter top, 15mm lower o-ring, USCAR connector\u003c\/li\u003e\n\u003cli\u003e[SPEC: CONFIRMED VEHICLE APPLICATIONS]\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Injector Dynamics","offers":[{"title":"Default Title","offer_id":43625774350403,"sku":"IDY 1300.48.14.15","price":259.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0064\/7754\/5539\/files\/injector-dynamics-idy-1300-48-14-15-29460807188550.jpg?v=1785794051","url":"https:\/\/www.tunedbyshawn.com\/products\/id1300-xds-fuel-injectors-single-injector-48mm-14mm-adapter-top-15mm-lower-o-ring-1300-48-14-15","provider":"Tuned by Shawn","version":"1.0","type":"link"}