{"product_id":"haltech-uc-10-digital-dash-ht-068000","title":"Haltech uC-10 Digital Dash (HT-068000)","description":"\u003cp\u003e\u003cstrong\u003eTen inches of optically bonded colour, and enough I\/O to run as its own data hub.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Haltech uC-10 is a 10 inch full colour digital dash with a 1280 x 480 optically bonded screen that stays readable in any light. Screen layouts are fully customisable in Haltech NSP, the same software you tune your Nexus with. It talks to Haltech CAN, OBD-II, and a range of aftermarket ECUs, or it can be wired in as a complete stand-alone unit and used as an I\/O expander in an existing Haltech setup.\u003c\/p\u003e\n\u003ch2\u003eWhat You'll See\u003c\/h2\u003e\n\u003cp\u003eA wide, crisp screen laid out exactly how you want it: gauges where your eyes land, warnings that demand attention, and a 14 LED RGB shift light across the top. Design your own pages in NSP, switch to a reverse camera feed when you need it, and let the twin ambient light sensors handle brightness from midday sun to a night session.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e10 inch full colour, optically bonded TFT screen, 1280 x 480 resolution\u003c\/li\u003e\n\u003cli\u003e600+ lumens, dimmable, with 2 onboard ambient light sensors\u003c\/li\u003e\n\u003cli\u003e70 degree minimum viewing angle, vertical and horizontal\u003c\/li\u003e\n\u003cli\u003eFully customisable screen layouts in Haltech NSP\u003c\/li\u003e\n\u003cli\u003e14 RGB shift lights\u003c\/li\u003e\n\u003cli\u003e512MB onboard looped datalogging\u003c\/li\u003e\n\u003cli\u003e6 digit odometer\u003c\/li\u003e\n\u003cli\u003eCamera input (composite video) with mirror and 0\/90\/180\/270 degree rotation, plus a dedicated 12V \/ 500mA camera power output\u003c\/li\u003e\n\u003cli\u003eWi-Fi, 2.4 GHz, with included glass mount antenna\u003c\/li\u003e\n\u003cli\u003eIP64 rated: dust-tight and protected against water splashes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eThe Details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSKU: HT-068000\u003c\/li\u003e\n\u003cli\u003eDimensions: 291.2 x 126.0 x 26.0 mm, excluding rear connectors\u003c\/li\u003e\n\u003cli\u003eOperating voltage: 6.5V to 20.0V\u003c\/li\u003e\n\u003cli\u003eAmbient temperature: -10 C (14 F) to +80 C (176 F)\u003c\/li\u003e\n\u003cli\u003eInputs and outputs: 10 x analog voltage inputs, 4 x synchronised pulsed inputs, 4 x digital pulsed outputs, 1 x 5V output, 1 x 12V output, 1 x signal ground, dedicated tacho input, dedicated alternator excite\u003c\/li\u003e\n\u003cli\u003eConnectors: 34 pin AMP Superseal (auxiliary), female RP-SMA (Wi-Fi antenna)\u003c\/li\u003e\n\u003cli\u003eCommunications: CAN (Haltech, OBD-II, or supported third party ECU), USB-A to USB-C\u003c\/li\u003e\n\u003cli\u003eCamera formats: NTSC 720 x 480, PAL 720 x 576\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eKit Includes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eHaltech uC-10 Digital Dash\u003c\/li\u003e\n\u003cli\u003e34 pin connector (same as HT-131001)\u003c\/li\u003e\n\u003cli\u003eHaltech DTM-4 to DTM-4 CAN cable, 3.0 m (118 in)\u003c\/li\u003e\n\u003cli\u003eUSB-C cable\u003c\/li\u003e\n\u003cli\u003e3 x M5 x 8 mm mounting screws\u003c\/li\u003e\n\u003cli\u003e2 x momentary switches, pre-terminated 800 mm 22AWG cable\u003c\/li\u003e\n\u003cli\u003eGlass mount Wi-Fi antenna (2.4 GHz)\u003c\/li\u003e\n\u003cli\u003eQuick Start Guide\u003c\/li\u003e\n\u003cli\u003eHaltech fabric keytag and stickers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eApplications\u003c\/h2\u003e\n\u003cp\u003eSuits all current Haltech ECUs via CAN. Also plug and play compatible with the following aftermarket ECU protocols: Hondata, Link G4, MaxxECU, Microtech, MoTeC M1 series, MoTeC hundred series (M400, M600, M800 gold box ECUs), and Syvecs. Can also be wired as a complete stand-alone dash.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot included \/ sold separately:\u003c\/strong\u003e OBD-II connection requires the OBD-II to CAN cable (HT-135003). Mounting hardware is not included: see the uC-10 Moulded Panel Mount (HT-060091), iC-7\/uC-10 Standard Dash Mount (HT-060070), and iC-7\/uC-10 Tube Mount (HT-060072). Reverse camera sold separately.\u003c\/p\u003e\n\u003cp\u003eUnsure about fitment for your build? Send us your engine and chassis details before ordering and we will confirm compatibility.\u003c\/p\u003e\n\u003cp\u003eTuned By Shawn is a Platinum Haltech Dealer. We can build the dash harness in house, and lay out your NSP screens and set up the uC-10 I\/O during a live remote tuning session over Zoom.\u003c\/p\u003e","brand":"Haltech","offers":[{"title":"Default Title","offer_id":40794656833603,"sku":"HT-068000","price":2160.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0064\/7754\/5539\/files\/HT-068000_00.jpg?v=1731634204","url":"https:\/\/www.tunedbyshawn.com\/products\/haltech-uc-10-digital-dash-ht-068000","provider":"Tuned by Shawn","version":"1.0","type":"link"}